Automatic Control, 6 credits

Reglerteknik, 6 hp

TSIU61

Main field of study

Electrical Engineering

Course level

First cycle

Course type

Programme course

Examiner

Inger Erlander Klein

Director of studies or equivalent

Johan Löfberg

Education components

Preliminary scheduled hours: 64 h
Recommended self-study hours: 96 h
ECV = Elective / Compulsory / Voluntary
Course offered for Semester Period Timetable module Language Campus ECV
6IKEA Chemical Analysis Engineering, B Sc in Engineering 5 (Autumn 2018) 1 2 Swedish Linköping, Valla E
6IDAT Computer Engineering, B Sc in Engineering (Embedded Systems) 5 (Autumn 2018) 1 2 Swedish Linköping, Valla E
6IDAT Computer Engineering, B Sc in Engineering (Software Engineering) 5 (Autumn 2018) 1 2 Swedish Linköping, Valla E
6IELK Engineering Electronics, B Sc in Engineering 3 (Autumn 2018) 1 2 Swedish Linköping, Valla C
6IMAS Mechanical Engineering, B Sc in Engineering 3 (Autumn 2018) 1 2 Swedish Linköping, Valla C

Main field of study

Electrical Engineering

Course level

First cycle

Advancement level

G1X

Course offered for

  • Engineering Electronics, B Sc in Engineering
  • Mechanical Engineering, B Sc in Engineering
  • Computer Engineering, B Sc in Engineering
  • Chemical Analysis Engineering, B Sc in Engineering

Entry requirements

Note: Admission requirements for non-programme students usually also include admission requirements for the programme and threshold requirements for progression within the programme, or corresponding.

Prerequisites

Calculus and Linear algebra

Intended learning outcomes

After completing this course students should be able to describe the basic requirements for and limitations of automatic control. Students should also be able to perform analysis and systematic construction of feedback control systems. This means that students will be expected to be able to do the following after completing this course:

  • Define basic concepts in the area of automatic control.
  • Transform mathematical models of linear dynamic systems between time domain input/output form and transfer function form.
  • Analyse models of linear dynamic systems that are given in the forms above with respect to stability, pole placement, rise time and damping.
  • Demonstrate the connections between the system properties of stability, rise time and damping in time and frequency domains.
  • Derive input/output signal relationships in feedback control systems using block diagram calculations.
  • Perform stability analysis of feedback control systems using Bode diagrams.
  • Construct regulators in PID-form and lead-lag form based on given specifications.
  • Perform simple robustness analysis of feedback control systems.
  • Formulate the specifications for a feedback control system for a lab-process, then model, construct and verify that system.

    Course content

    Dynamic systems. Feedback, PID-control. Differential equations. Transfer functions. Block diagram algebra. Stability. Frequency description. Compensation. Introduction to sensitivity and robustness. Control structures. Implementation. Simulation. Components.

    Teaching and working methods

    Lectures, lessons and laboratory work.

    Examination

    LAB1Laboratory Work1.5 creditsU, G
    TEN1Written Examination4.5 creditsU, 3, 4, 5

    Grades

    Four-grade scale, LiU, U, 3, 4, 5

    Department

    Institutionen för systemteknik

    Director of Studies or equivalent

    Johan Löfberg

    Examiner

    Inger Erlander Klein

    Course website and other links

    http://www.control.isy.liu.se/student/tsiu61/

    Education components

    Preliminary scheduled hours: 64 h
    Recommended self-study hours: 96 h

    Course literature

    Books

    • Glad T, Ljung L, Reglerteknik grundläggande teori

    Compendia

  • Code Name Scope Grading scale
    LAB1 Laboratory Work 1.5 credits U, G
    TEN1 Written Examination 4.5 credits U, 3, 4, 5

    Course syllabus

    A syllabus has been established for each course. The syllabus specifies the aim and contents of the course, and the prior knowledge that a student must have in order to be able to benefit from the course.

    Timetabling

    Courses are timetabled after a decision has been made for this course concerning its assignment to a timetable module. A central timetable is not drawn up for courses with fewer than five participants. Most project courses do not have a central timetable.

    Interrupting a course

    The vice-chancellor’s decision concerning regulations for registration, deregistration and reporting results (Dnr LiU-2015-01241) states that interruptions in study are to be recorded in Ladok. Thus, all students who do not participate in a course for which they have registered must record the interruption, such that the registration on the course can be removed. Deregistration from a course is carried out using a web-based form: www.lith.liu.se/for-studenter/kurskomplettering?l=sv. 

    Cancelled courses

    Courses with few participants (fewer than 10) may be cancelled or organised in a manner that differs from that stated in the course syllabus. The board of studies is to deliberate and decide whether a course is to be cancelled or changed from the course syllabus. 

    Regulations relating to examinations and examiners 

    Details are given in a decision in the university’s rule book: http://styrdokument.liu.se/Regelsamling/VisaBeslut/622678.

    Forms of examination

    Examination

    Written and oral examinations are held at least three times a year: once immediately after the end of the course, once in August, and once (usually) in one of the re-examination periods. Examinations held at other times are to follow a decision of the board of studies.

    Principles for examination scheduling for courses that follow the study periods:

    • courses given in VT1 are examined for the first time in March, with re-examination in June and August
    • courses given in VT2 are examined for the first time in May, with re-examination in August and October
    • courses given in HT1 are examined for the first time in October, with re-examination in January and August
    • courses given in HT2 are examined for the first time in January, with re-examination at Easter and in August.

    The examination schedule is based on the structure of timetable modules, but there may be deviations from this, mainly in the case of courses that are studied and examined for several programmes and in lower grades (i.e. 1 and 2). 

    • Examinations for courses that the board of studies has decided are to be held in alternate years are held only three times during the year in which the course is given.
    • Examinations for courses that are cancelled or rescheduled such that they are not given in one or several years are held three times during the year that immediately follows the course, with examination scheduling that corresponds to the scheduling that was in force before the course was cancelled or rescheduled.
    • If teaching is no longer given for a course, three examination occurrences are held during the immediately subsequent year, while examinations are at the same time held for any replacement course that is given, or alternatively in association with other re-examination opportunities. Furthermore, an examination is held on one further occasion during the next subsequent year, unless the board of studies determines otherwise.
    • If a course is given during several periods of the year (for programmes, or on different occasions for different programmes) the board or boards of studies determine together the scheduling and frequency of re-examination occasions.

    Registration for examination

    In order to take an examination, a student must register in advance at the Student Portal during the registration period, which opens 30 days before the date of the examination and closes 10 days before it. Candidates are informed of the location of the examination by email, four days in advance. Students who have not registered for an examination run the risk of being refused admittance to the examination, if space is not available.

    Symbols used in the examination registration system:

      ** denotes that the examination is being given for the penultimate time.

      * denotes that the examination is being given for the last time.

    Code of conduct for students during examinations

    Details are given in a decision in the university’s rule book: http://styrdokument.liu.se/Regelsamling/VisaBeslut/622682.

    Retakes for higher grade

    Students at the Institute of Technology at LiU have the right to retake written examinations and computer-based examinations in an attempt to achieve a higher grade. This is valid for all examination components with code “TEN” and "DAT". The same right may not be exercised for other examination components, unless otherwise specified in the course syllabus.

    Retakes of other forms of examination

    Regulations concerning retakes of other forms of examination than written examinations and computer-based examinations are given in the LiU regulations for examinations and examiners, http://styrdokument.liu.se/Regelsamling/VisaBeslut/622678.

    Plagiarism

    For examinations that involve the writing of reports, in cases in which it can be assumed that the student has had access to other sources (such as during project work, writing essays, etc.), the material submitted must be prepared in accordance with principles for acceptable practice when referring to sources (references or quotations for which the source is specified) when the text, images, ideas, data, etc. of other people are used. It is also to be made clear whether the author has reused his or her own text, images, ideas, data, etc. from previous examinations.

    A failure to specify such sources may be regarded as attempted deception during examination.

    Attempts to cheat

    In the event of a suspected attempt by a student to cheat during an examination, or when study performance is to be assessed as specified in Chapter 10 of the Higher Education Ordinance, the examiner is to report this to the disciplinary board of the university. Possible consequences for the student are suspension from study and a formal warning. More information is available at https://www.student.liu.se/studenttjanster/lagar-regler-rattigheter?l=sv.

    Grades

    The grades that are preferably to be used are Fail (U), Pass (3), Pass not without distinction (4) and Pass with distinction (5). Courses under the auspices of the faculty board of the Faculty of Science and Engineering (Institute of Technology) are to be given special attention in this regard.

    1. Grades U, 3, 4, 5 are to be awarded for courses that have written examinations.
    2. Grades Fail (U) and Pass (G) may be awarded for courses with a large degree of practical components such as laboratory work, project work and group work.

    Examination components

    1. Grades U, 3, 4, 5 are to be awarded for written examinations (TEN).
    2. Grades Fail (U) and Pass (G) are to be used for undergraduate projects and other independent work.
    3. Examination components for which the grades Fail (U) and Pass (G) may be awarded are laboratory work (LAB), project work (PRA), preparatory written examination (KTR), oral examination (MUN), computer-based examination (DAT), home assignment (HEM), and assignment (UPG).
    4. Students receive grades either Fail (U) or Pass (G) for other examination components in which the examination criteria are satisfied principally through active attendance such as other examination (ANN), tutorial group (BAS) or examination item (MOM).

    The examination results for a student are reported at the relevant department.

    Regulations (apply to LiU in its entirety)

    The university is a government agency whose operations are regulated by legislation and ordinances, which include the Higher Education Act and the Higher Education Ordinance. In addition to legislation and ordinances, operations are subject to several policy documents. The Linköping University rule book collects currently valid decisions of a regulatory nature taken by the university board, the vice-chancellor and faculty/department boards.

    LiU’s rule book for education at first-cycle and second-cycle levels is available at http://styrdokument.liu.se/Regelsamling/Innehall/Utbildning_pa_grund-_och_avancerad_niva. 

    Books

    Glad T, Ljung L, Reglerteknik grundläggande teori

    Compendia

    Note: The course matrix might contain more information in Swedish.

    I = Introduce, U = Teach, A = Utilize
    I U A Modules Comment
    1. DISCIPLINARY KNOWLEDGE AND REASONING
    1.1 Knowledge of underlying mathematics and science (G1X level)
    X
    TEN1
    
                                
    1.2 Fundamental engineering knowledge (G1X level)
    X
    X
    TEN1
    
                                
    1.3 Further knowledge, methods, and tools in one or several subjects in engineering or natural science (G2X level)
    
                                
    1.4 Advanced knowledge, methods, and tools in one or several subjects in engineering or natural sciences (A1X level)
    
                                
    1.5 Insight into current research and development work
    
                                
    2. PERSONAL AND PROFESSIONAL SKILLS AND ATTRIBUTES
    2.1 Analytical reasoning and problem solving
    X
    X
    LAB1
    TEN1
    
                                
    2.2 Experimentation, investigation, and knowledge discovery
    X
    X
    LAB1
    
                                
    2.3 System thinking
    X
    X
    LAB1
    TEN1
    
                                
    2.4 Attitudes, thought, and learning
    X
    TEN1
    
                                
    2.5 Ethics, equity, and other responsibilities
    
                                
    3. INTERPERSONAL SKILLS: TEAMWORK AND COMMUNICATION
    3.1 Teamwork
    X
    LAB1
    
                                
    3.2 Communications
    X
    LAB1
    
                                
    3.3 Communication in foreign languages
    X
    X
    TEN1
    
                                
    4. CONCEIVING, DESIGNING, IMPLEMENTING AND OPERATING SYSTEMS IN THE ENTERPRISE, SOCIETAL AND ENVIRONMENTAL CONTEXT
    4.1 External, societal, and environmental context
    X
    
                                
    4.2 Enterprise and business context
    
                                
    4.3 Conceiving, system engineering and management
    X
    X
    LAB1
    TEN1
    
                                
    4.4 Designing
    X
    X
    LAB1
    TEN1
    
                                
    4.5 Implementing
    X
    
                                
    4.6 Operating
    
                                
    5. PLANNING, EXECUTION AND PRESENTATION OF RESEARCH DEVELOPMENT PROJECTS WITH RESPECT TO SCIENTIFIC AND SOCIETAL NEEDS AND REQUIREMENTS
    5.1 Societal conditions, including economic, social, and ecological aspects of sustainable development for knowledge development
    
                                
    5.2 Economic conditions for knowledge development
    
                                
    5.3 Identification of needs, structuring and planning of research or development projects
    
                                
    5.4 Execution of research or development projects
    
                                
    5.5 Presentation and evaluation of research or development projects
    
                                

    This tab contains public material from the course room in Lisam. The information published here is not legally binding, such material can be found under the other tabs on this page.

    There are no files available for this course.